AMSOIL Sirocco^TM Synthetic Compressor Oil

(SEI) ISO-32/46
For Rotary and Reciprocating Compressors

AMSOIL SIROCCO Synthetic Compressor Oil (SEI) is recommended as a direct replacement for PAG compressor oils such as Sullair Sullube 32 and Ingersoll-Rand SSR Ultra-coolant. Not recommended for use with Silicone base fluids.

Product Code:SEI

Note: Refer to "Product Lookup Guide" located in the top left menu for your specific application needs

More Information/Pricing

AMSOIL SIROCCO Synthetic Compressor Oil (SEI) is formulated with premium synthetic ester technology. This high-quality, long-life fluid lasts several times longer in use than mineral-based oils. AMSOIL SIROCCO Compressor Oil is fully formulated with nondetergent additives and is designed for use in rotary screw compressors and vacuum pumps. SIROCCO effectively protects against wear, oxidation, foam and rust and has inherent lubricity and good thermal conductivity which allow it to reduce heat and energy consumption. AMSOIL SIROCCO Compressor Oil increases operating efficiency, reducing money spent on energy, repair and maintenance costs.

AMSOIL SE Series Synthetic Ester Compressor Oil/Coolants maintain performance across a wide operating temperature range. The low pour points, high viscosity indices and lack of paraffin's (wax) make these excellent all season lubricants.

At high temperatures, SE Series Synthetic Ester Compressor Oil/Coolants form virtually no carbon, allowing for clean operation. At cold temperatures, equipment starts easier and the lubricant is quickly pumped to critical components, preventing lubricant starvation and excessive wear. SE Series Synthetic Ester Compressor Oil/Coolants also resist water to prevent damaging Oils/water emulsions, allowing for longer lubricant life and ease of water removal from the sump.

PERFORMANCE FEATURES

Resists foaming
Rust and oxidation inhibited
Readily separates from water
Recommended for use in rotary screw and reciprocating compressors
Long-life/extended drain performance
Compatible with polyglycol fluids such as Sullube 32 and Ingersoll-Rand SSR Ultra-coolant
SEI is biodegradable under the CEC-L33-A94 standard

SAFETY ADVANTAGE

AMSOIL SE Series Synthetic Ester Compressor Oil/Coolants have higher flash, fire and auto ignition points than competitive petroleum Oil. Their resistance to carbon formation and the ashless additive system minimize the incidence of deposits acting as ignition-promoting hot spots. Although AMSOIL SE Series increase fire safety, they cannot be considered non-flammable.

APPLICATION RECOMMENDATION

AMSOIL SEI is a multi-viscosity Oils meeting the requirements of 5w-20. It may be used in applications calling for either an ISO-32 or ISO-46 compressor Oils or coolant. It is recommended for use in single and multi-stage rotary screw compressors and vacuum pumps that call for this viscosity.

When installing AMSOIL SEI, it is recommended that the old Oils be thoroughly drained and if warranted, the system cleaned. If a lot of carbon or residue is found on the internal compressor parts, follow the manufacturer's recommendations for removal prior to installing the new Oils. AMSOIL SE Series Synthetic Ester Compressor Oil/Coolants have a high level of solvency and may remove deposits left in the system. Check the filters and Oils/air separators regularly for the first 500 hours of operation and replace as necessary.

AMSOIL SEI is compatible with and recommended as a replacement for much higher priced polyalkylene glycol (PAG) compressor Oil or coolants such as Sullube 32 and Ingersoll Rand SSR Ultra Coolant. No flushing is necessary when changing over from Glycol Coolants to AMSOIL SEI. However, draining the system and changing the filters is recommended.

AMSOIL SEI is recommended for use up to 8,000+ hours for most compressor applications. However, this is subject to operating conditions and maintenance practices.* Monitoring by Oils analysis every 1,000 hours is recommended.

* Where discharge temperature exceeds 205F, lubricant life expectancy is reduced.

COMPATIBILITY

AMSOIL SEI is compatible with petroleum Oil, most synthetic engine oil*, and many seals, paints and materials commonly used in compressors. Materials recommended and not recommended for use with SEI Oil/coolants are listed below. For additional information, see the AMSOIL Compatibility Guide (G-1274) or consult your AMSOIL Dealer or AMSOIL.

*AMSOIL SE Series is NOT RECOMMENDED as a replacement or for use with the silicone based compressor Oils Sullube 24KT. AMSOIL SE Series is NOT RECOMMENDED for use in "Breathing Air or Refrigeration" compressors.

NOT RECOMMENDED

Seals - Neoprene, SBR Rubber, Low Nitrile Buna N
Paints - Acrylic Paint, Lacquer
Plastics - Polystyrene, Polycarbonate Plastic, PVC, ABS

NOTE: Process gasses suitable for use with the SE Series:

Nitrogen, hydrogen, helium, carbon monixide, carbon dioxide (dry), ethylene, methane, propane, butane, propylene, butylene, natural gas, benzene, butadiene, furnace (crack gas), hydrogen sulfide (dry), sulfur hexafluoride, synthetic gas, sulfur dioxide.