AMSOIL PC Series Compressor Oil

AMSOIL Synthetic PC Series Compressor Oil are made from high quality, shear stable synthetic base Oil. PC Series Oil provide long compressor life through reduced component wear, corrosion protection, water resistance and lubricant breakdown resistance. These Oil reduce maintenance costs by extending drain intervals and lowering labor and used product disposal requirements.

Product Codes: PCH, PCI, PCJ, PCK, PCL (see table below)

AMSOIL Synthetic Base Oils Technology

AMSOIL’s unique formulation of synthetic base Oil combine the advantages of esters and polyalphaolefins (PAO's) into one balanced product. The high viscosity indices, low pour points, low volatility and prolonged thermal stability allow for use in a wide operating temperature range. These Oil minimize carbon build-up, provide clean performance and exhibit low frictional characteristics. This superior formulation has demonstrated increased operational efficiency, reduced energy consumption and lower operating temperatures.

AMSOIL Compressor Oils Additives - A Thorough System for Top Performance

The anti-foam agents stop unwanted foaming and air entrainment. Corrosion inhibitors prevent rust and corrosion caused by water and process contaminants, and oxidation inhibitors extend lubricant life and prevent carbon formation. The PC Series is fortified with ashless, non-detergent additives designed to increase the length of compressor serviceability.

Pricing

Stable in the Presence of Water

AMSOIL PC Series exhibit very good hydrolytic stability, and they readily separate from water. This prevents acid formation and unwanted Oils/water emulsions. These features allow water to be easily drained from the sump and extends the life of a lubricant.

Safety Advantage

AMSOIL PC Series Compressor Oil have higher flash, fire and auto-ignition points than competitive petroleum Oil. Also, their resistance to carbon formation and the ashless additive system minimize the incidence of deposits acting as ignition-promoting hot spots. Although AMSOIL PC Series Compressor Oil have high fire points, they cannot be considered non-flammable.

PERFORMANCE FEATURES

Anti-foam, anti-wear protection
Rust and oxidation inhibited
Suitable for use in rotary screw, vane, centrifugal and reciprocating compressors
Combines advantages of ester and PAO technology
Excellent compatibility with components and other Oil

APPLICATION RECOMMENDATION

The manufacturer's recommended viscosity grade of AMSOIL PC Series Oil is recommended for use in single and multi-stage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps and other compressor applications. In addition, the correct viscosity may be used in light duty gear and bearing applications, blowers, pumps and hand-held pneumatic tools.

PC Series Synthetic Compressor Oil are recommended for use in a wide temperature range, from 20F above the pour point to 275F discharge temperature.
The PC Series may be used up to 8000 hours for many compressor applications.* This drain interval is subject to operating conditions and maintenance practices. Monitoring by Oils analysis at 500-hour intervals is recommended.
PC Oil are compatible with petroleum Oil, most synthetic engine oil,** and almost all seals, paints and materials commonly used in compressors. It is suggested that the compressor be thoroughly drained and cleaned if warranted, and the filter be changed prior to filling with the new lubricant. Cleaning should be done in accordance with manufacturer's recommendations. Consult AMSOIL technical department where further recommendations are needed.

AMSOIL PRODUCT COMPATIBILITY

PC Series Compressor Oil are not recommended for "breathing air" or refrigeration compressors; they are also not recommended for use with poly carbonate plastic that is not metal covered, PVC plastic, butyl, ethylene-propylene and SBR rubber.

The following process gases are suitable for use with PC Series Compressor Oil: nitrogen, hydrogen, helium, carbon monoxide, carbon dioxide (dry), ethylene, methane, propane, butane, propylene, butylene, natural gas, benzene, butadiene, furnace (crack gas), hydrogen sulfide (dry), sulfur hexafluoride, synthetic gas, sulfur dioxide.

AMSOIL PRODUCT AVAILABILITY

AMSOIL PC Series Compressor Oil are available in 5-gallon pails, 55-gallon drums, 275-gallon totes and bulk quantities.

AMSOIL Industrial Lubricants are stocked in Superior, Wisconsin and in select regional distribution centers throughout the United States and Canada.

Typical Technical Properties

Synthetic PC Series Compressor Oil	AMSOIL Product Codes and Specifications
	PCH ISO 32 SAE 10W	PCI ISO 46 SAE 20	PCJ ISO 68 SAE 30	PCK ISO 100 SAE 40	PCL ISO 150 SAE 50
ISO VG - ASTM D-2422	32	46	68	100	150
VK 100C - ASTM D-445	5.8	7.8	10.3	13.5	17.5
VK 40C - ASTM D-445	30.8	47.2	68.2	102.3	150
Viscosity Index - ASTM D-2270	131	132	137	132	128
SPGR - ASTM D-1298	0.8473	0.8519	0.8565	0.8597	0.8670
Density - ASTM D-1298	7.055	7.093	7.132	7.158	7.219
Flash Point C (F) - ASTM D-92	264 (507)	258 (496)	262 (504)	264 (507)	256 (493)
Fire Point C (F) - ASTM D-92	276 (529)	276 (529)	278 (532)	278 (532)	276 (529)
Pour Point C (F) - ASTM D-97	-54 (-65)	-51 (-60)	-48 (-54)	-45 (-49)	-38 (-36)
Four-Ball Wear Test - ASTM D-4172 (40 kg, 1200 rpm, 75 C, 60 min.)	0.45	0.45	0.45	0.40	0.40
Copper Strip Corrosion Test - ASTM D-130	1A	1A	1A	1A	1A
Rust Test - ASTM D665 A & B Fresh Water and Synthetic Sea Water	Pass	Pass	Pass	Pass	Pass
Foam, ml (ASTM D-892) Sequence I, II, III Test End - and After 10 minutes settling	0/0/0	0/0/0	0/0/0	0/0/0	0/0/0
Demulsibility ASTM D-1401 [Oils/water/cuff (minutes)]	40/40/0 (15)	40/40/0 (15)	40/40/0 (15)	40/40/0 (10)	40/40/0 (10)

* Where discharge temperature exceeds 205F, lubricant life expectancy is reduced.

** Not compatible with silicon or polyglycol fluids such as Sullair 24KT, Sullube 32 and Ingersoll Rand SSR Ultra Coolant

Product Codes: PCH, PCI, PCJ, PCK, PCL

Back to top of page